View UPG2163T5N_4486430.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
GaAs INTEGRATED CIRCUIT
PG2163T5N
SPDT SWITCH FOR 2.4 GHz AND 6 GHz DUAL-BAND WIRELESS LAN
DESCRIPTION
The PG2163T5N is GaAs MMIC SPDT (Single Pole Double Throw) switch which was developed for 2.4 GHz and 6 GHz dual-band wireless LAN. This device can operate frequency from 2.4 GHz band and 6 GHz band, having the low insertion loss and high isolation. This device is housed in a 6-pin plastic TSON (Thin Small Out-line Non-leaded) package. And this package is able to high-density surface mounting.
FEATURES
* Operating frequency * Switch control voltage * Low insertion loss * High isolation * Handling power : f = 2.4 to 2.5 GHz and 4.9 to 6.0 GHz : Vcont (H) = 2.8 to 5.0 V (3.0 V TYP.) : Vcont (L) = -0.3 to 0.3 V (0 V TYP.) : Lins1 = 0.40 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Lins2 = 0.50 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL1 = 38 dB TYP. @ f = 2.4 to 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : ISL2 = 30 dB TYP. @ f = 4.9 to 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +31.0 dBm TYP. @ f = 2.5 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V : Pin (1 dB) = +29.0 dBm TYP. @ f = 6.0 GHz, Vcont (H) = 3.0 V, Vcont (L) = 0 V * High-density surface mounting : 6-pin plastic TSON package (1.5 x 1.5 x 0.37 mm)
APPLICATIONS
* Dual-band wireless LAN (IEEE802.11a + b/g)
ORDERING INFORMATION
Part Number Order Number Package 6-pin plastic TSON (Pb-Free) Marking G4X Supplying Form * Embossed tape 8 mm wide * Pin 1, 6 face the perforation side of the tape * Qty 3 kpcs/reel
PG2163T5N-E2
PG2163T5N-E2-A
Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: PG2163T5N
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version.
Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information.
Document No. PG10626EJ02V0DS (2nd edition) Date Published February 2008 NS Printed in Japan
The mark shows major revised points.
2006, 2008
The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field.
PG2163T5N
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
(Top View) (Top View) (Bottom View)
Pin No. 1 Pin Name GND Vcont2 OUT2 (RX) OUT1 (TX) Vcont1 IN (ANT)
1
6
1
6
6
1
2 3
G4X
Vcont1 High Low Parameter Parameter
2
5
2
5
5
2
4 5 6
3
4
3
4
4
3
Remark Exposed pad : GND
TRUTH TABLE
Vcont2 Low High IN (ANT)-OUT1 (TX) OFF ON IN (ANT)-OUT2 (RX) ON OFF
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Symbol Vcont Pin TA Tstg Ratings -6.0 to +6.0 +32 -45 to +85 -55 to +135 Unit V dBm C C
Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Symbol Vcont (H) Vcont (L) f1 f2 MIN. 2.8 -0.3 2.4 4.9 TYP. 3.0 0 - - MAX. 5.0 0.3 2.5 6.0 Unit V V GHz GHz
Switch Control Voltage (H) Switch Control Voltage (L) Operating Frequency 1 Operating Frequency 2
2
Data Sheet PG10626EJ02V0DS
PG2163T5N
ELECTRICAL CHARACTERISTICS (TA = +25C, Vcont (H) = 3.0 V, Vcont otherwise specified)
Parameter Insertion Loss 1 Insertion Loss 2 Isolation 1 Isolation 2 Input Return Loss 1 Input Return Loss 2 Output Return Loss 1 Output Return Loss 2 1 dB Loss Compression Note Input Power 1 1 dB Loss Compression Note Input Power 2 Input 3rd Order Intercept Point Switch Control Current Switch Control Speed Symbol Lins1 Lins2 ISL1 ISL2 RLin1 RLin2 RLout1 RLout2
(L)
= 0 V, Z0 = 50 , DC blocking capacitors = 4 pF, unless
Test Conditions f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz f = 2.4 to 2.5 GHz f = 4.9 to 6.0 GHz
MIN. - - 35 27 - - - - - - - -
TYP. 0.40 0.50 38 30 15 15 15 15 +31.0
MAX. 0.60 0.80 - - - - - - - - - 1.0 -
Unit dB dB dB dB dB dB dB dB dBm
Pin (1 dB) 1 f = 2.4 to 2.5 GHz
Pin (1 dB) 2 f = 4.9 to 6.0 GHz
+29.0
dBm
IIP3 Icont tSW 50% CTL to 90/10%
+55 0.1 50
dBm
A
ns
-
Note Pin
(1 dB)
is measured the input power level when the insertion loss increases more 1 dB than that of linear
range. Caution This device is used it is necessary to use DC blocking capacitors.
Data Sheet PG10626EJ02V0DS
3
PG2163T5N
EVALUATION CIRCUIT
4 pF 1 6 IN (ANT)
Vcont2 1 000 pF
2
5 1 000 pF
Vcont1
OUT2 (RX) 4 pF
3
4 4 pF
OUT1 (TX)
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
4
Data Sheet PG10626EJ02V0DS
PG2163T5N
MOUNTING PAD AND SOLDER MASK LAYOUT DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm)
MOUNTING PAD
0.3 0.5 0.3
1.0
0.3 0.2
0.3
SOLDER MASK
0.475 0.25 0.475
0.35 0.55 0.15
0.25
Solder thickness : 0.08 mm
Remark The mounting pad and solder mask layouts in this document are for reference only.
0.5
0.5
0.5
0.5
Data Sheet PG10626EJ02V0DS
5
PG2163T5N

PACKAGE DIMENSIONS 6-PIN PLASTIC TSON (UNIT: mm)
(Top View)
1.50.1
(Side View)
(Bottom View)
0.30.07
0.50.06
1.50.1
0.37+0.03 -0.05
0.20.1
0.2+0.07 -0.05
0.70.1
6
Data Sheet PG10626EJ02V0DS
1.20.1
PG2163T5N
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260
For soldering
Preheating temperature (package surface temperature) : 120C or below
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PG10626EJ02V0DS
7
PG2163T5N
* The information in this document is current as of February, 2008. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above).
M8E 02. 11-1
8
Data Sheet PG10626EJ02V0DS
PG2163T5N
Caution
GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth.

▲Up To Search▲

Price & Availability of UPG2163T5N

	To Download UPG2163T5N Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .